Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Scottsdale Homeowners
Most chimney problems in Scottsdale announce themselves quietly: a stain on the ceiling board, a puff of smoke that rolls back into the room, mortar that crumbles when you brush it. By the time a crack is visible from the driveway, water has usually been finding its way in for a while. We’re Scottsdale Chimney Sweep, and repair is one of three services we handle, alongside sweeping and inspection. Our technicians have up to experience, and we work from documentation, not guesswork. When you call (888) 340-2124, we can often line up same-day service, and we answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Chimney Cap Installation
Chimney Cap Installation is the fitting of a protective cover over the flue opening, sized to the crown and sealed at the edge. A good cap keeps rain, debris, and animals out of the flue while letting smoke and gases escape. In Scottsdale, caps earn their keep against dust and monsoon-driven rain that runs down an open flue and soaks the smoke chamber. We measure the flue, choose a cap that matches the masonry, and anchor it so wind doesn’t shift it. Installation usually runs $250-$650 installed, depending on cap style and flue size. A written estimate sets the final price.
Choosing the Right Cap Style
Single-flue caps, multi-flue caps, and caps with mesh screens each solve different problems. A screen matters if birds or squirrels have been getting in; a solid-top design matters more where driving rain is the issue. We’ll tell you which we’re using and why before we order it.
When a Cap Should Be Added
A newly built or relined flue always deserves a cap, and so does any chimney that has sat uncapped through a rainy season. If your flue is open to the sky right now, it’s worth having us look before the next storm season. Small job, real protection.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Cap Replacement
Chimney Cap Replacement is the swap-out of a failed, rusted, or undersized cap for one that actually fits the flue and seals properly. Caps take a beating from sun and monsoon weather, and rusted mesh or a warped top lets water and animals straight through. We remove the old cap, inspect the flue opening while it’s exposed, and fit a replacement sized to your chimney. Most replacements run $250-$650, with the number depending on whether the existing anchor points are sound and what style you choose. We document the condition of the crown and flue at the same time, since that’s the moment to catch problems.
Signs the Old Cap Has Failed
Rust streaks, a loose or tilted cap, torn mesh, or a cap sitting crooked after a windstorm all point to replacement rather than patching. Once the mesh tears, birds and debris get in fast. Don’t wait for a flue blockage to confirm it.
Matching Cap to Flue
An oversized cap lets water blow in under the edges; an undersized one sits loose and rattles in wind. We match the cap to the measured flue opening and the crown dimensions. Famco and Copperfield cap lines are among the products we work with, and we’ll explain the choice.
Chimney Liner Installation
Chimney Liner Installation is the placement of a new flue liner, either a flexible stainless system or a resurfaced liner, to contain combustion gases and protect the surrounding masonry. Original clay tile liners crack, spall, and separate over time, and a damaged liner lets heat and gases reach structures that were never meant to hold them. This is a safety-critical repair, not a cosmetic one. We can install DuraFlex flexible stainless liners for deteriorated or mismatched flues, and we apply HeatShield resurfacing where the existing liner can be restored rather than replaced. Both are professional-grade systems installed by trained applicators. Liner work is priced per job after inspection; the written estimate sets the final price.
Flexible Stainless vs. Resurfacing
DuraFlex flexible liners suit flues that are offset, misaligned, or too far gone to resurface. HeatShield fills and smooths cracks in a liner that still has enough structure to hold. We diagnose which applies before recommending either.
Do You Really Need a New Liner?
Not always. A camera inspection tells us whether the cracks are surface-level or structural. We show you the footage and photo report before you commit to anything, and if a liner can safely wait a season, we’ll say so.
Chimney Flashing Repair
Chimney Flashing Repair is the correction of the metal sealing where the chimney meets the roof, the joint most likely to leak on any home. Flashing fails when sealant dries out, fasteners back out, or the metal itself corrodes and pulls away from the shingles. In Scottsdale, sun bakes sealant until it cracks, and one good monsoon finds the gap. We reset or replace the flashing, reseal the joint correctly, and check the roof deck around it for water damage. Flashing work typically runs $300-$800 depending on the roof pitch and how much of the flashing needs replacing. The written estimate confirms the price.
Reading a Leak Source
A ceiling stain near the chimney is flashing until proven otherwise. Water can travel along framing before it shows, so the stain is rarely directly under the gap. That’s why we inspect the whole joint, not just the visible seal.
Repair vs. Full Replacement
Loose fasteners and failed sealant are a repair. Rusted-through metal or flashing that’s been incorrectly installed needs replacement. We tell you which you have, with photos of the joint before and after.
Chimney Crown Repair
Chimney Crown Repair is the fixing or rebuilding of the concrete cap at the top of the chimney, the surface that sheds water away from the flue and masonry below. A cracked crown lets water soak into the chimney body, which then shows up as interior stains, spalled brick, or a rusted damper. We remove deteriorated concrete, form a proper slope, and finish it so water runs off instead of pooling. Crown repair commonly runs $400-$1,200 depending on the size of the chimney and whether the crown can be patched or needs to be recast. A written estimate sets the final price before any work starts.
Why Crowns Crack
Heat from below, sun from above, and the natural settling of masonry all stress a crown over time. Thin pours and flat tops crack first. A correctly sloped crown lasts far longer than a patched one.
Water Damage Below the Crown
Staining on the smoke chamber, rusted damper hardware, and crumbling mortar near the top are all signs water has been getting past the crown. We check the flue interior for the same damage before we finish the top.
Chimney Repair Companies
Chimney Repair Companies vary widely in what they actually do, and in Scottsdale the difference usually shows up in the diagnosis. Some outfits sweep and hand you a list of recommended repairs with no evidence behind it; others are general handymen who take chimney work between other jobs. We’re a chimney specialist, not a general home-services operation, and every technician’s skill set is built around one system. Repair, sweeping, and inspection are handled by the same company start to finish. We document what we find with camera footage and a photo report before recommending anything, so you can see the problem yourself. Repair pricing depends on scope; the written estimate sets the final figure.
Questions Worth Asking
Ask whether the company does chimney work exclusively, whether they carry the products they install, and whether they’ll show you the camera footage. Vague answers on any of those are your cue to keep looking. A specialist will answer all three without flinching.
Beware the Low Bid
A bid well below the rest usually skips the inspection that justifies the work. If a company is willing to quote a liner over the phone, they’re guessing. We won’t price structural work without seeing it first.
Chimney Masonry Repair
Chimney Masonry Repair is the restoration of the brick, mortar, and stone that make up the chimney structure, from repointing joints to rebuilding sections damaged by water or heat. Crumbling mortar and spalling brick aren’t just cosmetic. Once joints erode, water gets behind the brick, and the chimney starts losing structural integrity from the inside out. We grind out failed mortar and repoint with a mix suited to the masonry, replace spalled brick, and rebuild where a section has gone too far. Masonry work typically runs $500-$2,500 depending on how much needs repointing or replacing. A free written estimate sets the final price, and nothing gets recommended without documented evidence.
Repointing vs. Rebuilding
Repointing restores the joints when the brick itself is still sound. Rebuilding replaces brick that has spalled or crumbled. We inspect the whole chimney face to determine which is needed and show you the areas in question.
Water and Masonry
Most masonry damage here traces back to water: a failing crown, bad flashing, or an uncapped flue. Repairing the brick without fixing the source just resets the clock. We address the cause first.
Brands We Service
We work with six industry-recognized product lines, which gives us real choices rather than a single shelf of options. HeatShield is the industry’s leading resurfacing system for liner repair, and it’s a product only trained applicators are qualified to install; we apply it where the existing flue can be restored instead of replaced. DuraFlex flexible stainless liner systems let us address deteriorated or mismatched flues with a solution built for the shape of the flue, not a compromise forced into it.
Famco and Copperfield cover caps and related components, sized properly to the chimney rather than improvised on site. We service Gelco and Olympia Chimney products as well, and we know where each tends to wear. Whether you have Famco or any other make, we can help, and we’ll tell you exactly which product we’re specifying and why.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Water stains on the ceiling or chimney breast. Staining means water is already inside the structure, usually through the flashing or crown. Left alone, it reaches framing and insulation. The longer it runs, the larger the repair.
- Crumbling mortar or spalling brick. If mortar crumbles when you brush it or brick faces are flaking, the chimney is losing structural integrity. Repointing early costs far less than rebuilding later.
- Smoke rolling back into the room. Backdraft can point to a blocked flue, a damaged liner, or a chimney that isn’t drafting properly. It’s also a sign to stop using the fireplace until it’s checked.
- A rusted damper or firebox hardware. Rust inside the firebox means moisture has been getting in from above. The source is almost always the crown or the cap, and it needs to be found.
- Loose or visibly damaged flashing. Flashing that’s pulling away from the roof or shingles is an open door for water. A simple repair now prevents deck and ceiling damage later.
Our Process, Step by Step
- 1
We start with inspection, not a sales pitch. A camera run through the flue shows us the liner, smoke chamber, and any offsets. We photograph what we find so you’re looking at the same evidence we are.
- 2
We document findings in a photo report. Every recommended repair is tied to a specific finding, with images you keep. If something can wait, we say so plainly.
- 3
We write the estimate before any work begins. Line items, materials, and brand specified, all in writing. You’ll know which liner or cap we’re using and why.
- 4
We do the repair with professional-grade materials. HeatShield for liner resurfacing, DuraFlex for flexible stainless installations, and masonry mixes matched to your chimney’s brick. No substitutions mid-job without your sign-off.
- 5
We verify and close out. After the repair we check the work and leave you with the documentation. If you want the chimney swept afterward, that’s chimney repair follow-through we handle ourselves, no second contractor needed.
How Much Does Chimney Repair Cost in Scottsdale?
Chimney repair in Scottsdale generally runs from a few hundred dollars for a cap or flashing fix up to several thousand for a full liner installation or masonry rebuild. A typical cap installation or replacement runs $250-$650 depending on style and flue size. Flashing repair usually lands between $300 and $800, and crown repair between $400 and $1,200. Masonry repointing and brick replacement commonly run $500-$2,500 depending on how much of the chimney face is affected. Liner work is priced per job after inspection, since DuraFlex installation and HeatShield resurfacing carry different scopes.
What affects the price: roof pitch and access, the size of the chimney, how much of the original material can be saved, and which product system applies. How to avoid overpaying is simple. Ask for the camera footage, ask which brand and product is being specified, and ask whether any part of the work can safely wait a season. What’s included in a free estimate is the inspection, the photo report, and a written line-item estimate. Nothing is recommended without camera evidence you can see for yourself. Call (888) 340-2124 for an exact quote.
Our Service Area Near Scottsdale
We serve Scottsdale and the surrounding Valley communities, including Phoenix, Tempe, Mesa, Glendale, Peoria, and Youngtown, along with outlying areas like Black Canyon City, Wittmann, Tonto Basin, and Young. Response times vary by distance, and larger repair jobs are scheduled around the inspection. If you’re in Phoenix and need chimney repair, we cover it the same way we do here. For Tempe homeowners, chimney repair is a short trip for our technicians, and we book it into the same schedule. Same-day service is often possible; call to check availability.
Serving Scottsdale, AZ – Our Local Coverage Area
We serve Scottsdale and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Chimney Repair in Scottsdale
Chimney repair covers the fixes that restore a chimney’s structure and function, from caps and flashing to liners, crowns, and masonry. It’s distinct from sweeping, which removes creosote and debris, and from inspection, which documents condition. We handle all three so the diagnosis and the repair come from the same company.
Most single-item repairs like a cap, flashing, or crown are done in a day. Liner installation and masonry rebuilds can take longer depending on scope and material drying. Your written estimate includes the expected schedule, and we confirm it before work starts.
Typical repairs range from $250-$650 for caps up to $500-$2,500 for masonry work, with liners priced per job. The written estimate sets the final price, and the estimate itself is free. Call (888) 340-2124 for an exact quote.
Yes. We install DuraFlex flexible stainless liner systems and apply HeatShield resurfacing, and we work with Famco, Copperfield, Gelco, and Olympia Chimney products as well. We’ll tell you exactly which system applies to your flue and why.
Same-day service is often available, so call and we’ll check the schedule. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm.
Our workmanship is backed by a satisfaction guarantee, and product warranties follow the manufacturer of the system installed. We walk through what’s covered before you sign the estimate. Ask us and we’ll put it in writing.
Clear access to the fireplace and hearth, and let us know about pets or gates. If roof access is needed, we’ll confirm it when we book. You don’t need to do anything else; the inspection and documentation are on us.
Schedule Your Chimney Repair Service in Scottsdale Today
If something about your chimney doesn’t look right, the fastest way to know is to have it looked at properly. Call Scottsdale Chimney Sweep at (888) 340-2124 for a free, no-obligation estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. We’ll inspect, document, and quote in writing before any work begins.
Written by the team at Scottsdale Chimney Sweep.